8.5 KiB
Tutorial: Working with Dynamixel Servos
In this tutorial, we will go into the details with Dynamixel servos and Stretch.
Overview
Stretch comes with two Dynamixel buses - one for the head and one for the end-of-arm:
ls /dev/hello-dynamixel-*
Output:
/dev/hello-dynamixel-head /dev/hello-dynamixel-wrist
Typically, users will interact with these devices through either the Head or the EndOfArm interfaces. This tutorial is for users looking to work directly with the servos from the provided servo tools or through Stretch Body's low-level Dynamixel API.
Servo Tools
!!! note The servo tools here are part of the Stretch Factory package which is installed as a part of Stretch Body.
Jogging the Servos
You can directly command each servo using the command line tool REx_dynamixel_servo_jog.py. This can be useful for debugging new servos added to the end-of-arm tool during system bring-up. For example, to command the head pan servo:
REx_dynamixel_jog.py /dev/hello-dynamixel-head 11
Output:
[Dynamixel ID:011] ping Succeeded. Dynamixel model number : 1080. Baud 115200
------ MENU -------
m: menu
a: increment position 50 tick
b: decrement position 50 tick
A: increment position 500 ticks
B: decrement position 500 ticks
v: set profile velocity
u: set profile acceleration
z: zero position
h: show homing offset
o: zero homing offset
q: got to position
p: ping
r: reboot
w: set max pwm
t: set max temp
i: set id
d: disable torque
e: enable torque
x: put in multi-turn mode
y: put in position mode
w: put in pwm mode
f: put in vel mode
-------------------
Rebooting the Servos
Under high-load conditions, the servos may enter an error state to protect themselves from thermal overload. In this case, the red LED on the servo will flash (if visible). In addition, the servo will be unresponsive to motion commands. In this case, allow the overheating servo to cool down and reboot the servos using the stretch_robot_dynamixel_reboot.py tool:
stretch_robot_dynamixel_reboot.py
Output:
For use with S T R E T C H (TM) RESEARCH EDITION from Hello Robot Inc.
Rebooting: head_pan
[Dynamixel ID:011] Reboot Succeeded.
Rebooting: head_tilt
[Dynamixel ID:012] Reboot Succeeded.
Rebooting: stretch_gripper
[Dynamixel ID:014] Reboot Succeeded.
Rebooting: wrist_yaw
[Dynamixel ID:013] Reboot Succeeded.
Identify Servos on the Bus
If it is unclear which servos are on the bus, and at what baud rate, you can use the REx_dynamixel_id_scan.py tool. Here we see that the two head servos are at ID 11 and 12 at baud 57600.
REx_dynamixel_id_scan.py /dev/hello-dynamixel-head
Output:
Scanning bus /dev/hello-dynamixel-head at baud rate 57600
----------------------------------------------------------
Scanning bus /dev/hello-dynamixel-head
Checking ID 0
Checking ID 1
Checking ID 2
Checking ID 3
Checking ID 4
Checking ID 5
Checking ID 6
Checking ID 7
Checking ID 8
Checking ID 9
Checking ID 10
Checking ID 11
[Dynamixel ID:011] ping Succeeded. Dynamixel model number : 1080. Baud 115200
Checking ID 12
[Dynamixel ID:012] ping Succeeded. Dynamixel model number : 1060. Baud 115200
Checking ID 13
Checking ID 14
Checking ID 15
Checking ID 16
Checking ID 17
Checking ID 18
Checking ID 19
Checking ID 20
Checking ID 21
Checking ID 22
Checking ID 23
Checking ID 24
Setting the Servo Baud Rate
Stretch ships with its Dynamixel servos configured to baudrate=115200. When adding your servos to the end-of-arm tool, you may want to set the servo baud using the REx_dynamixel_set_baud.py tool. For example:
REx_dynamixel_set_baud.py /dev/hello-dynamixel-wrist 13 115200
Output:
---------------------
Success at changing baud. Current baud is 115200 for servo 13 on bus /dev/hello-dynamixel-wrist
!!! note Earlier units of Stretch RE1 may be running Dynamixel servos at baud 57600.
Setting the Servo ID
Dynamixel servos come with ID=1 from the factory. When adding your servos to the end-of-arm tool, you may want to set the servo ID using the REx_dynamixel_id_change.py tool. For example:
REx_dynamixel_id_change.py /dev/hello-dynamixel-wrist 1 13
Output:
[Dynamixel ID:001] ping Succeeded. Dynamixel model number : 1080. Baud 115200
Ready to change ID 1 to 13. Hit enter to continue:
[Dynamixel ID:013] ping Succeeded. Dynamixel model number : 1080. Baud 115200
Success at setting ID to 13
Stretch Body Dynamixel API
Stretch Body's low-level Dynamixel API includes a hierarchy of three classes
| Class |
|---|
| DynamixelXChain |
| DynamixelHelloXL430 |
| DynamixelXL430 |
!!! note The naming of XL430 is for legacy reasons. These classes will work with all X Series servos.
DynamixelXChain
DynamixelXChain manages a set of daisy-chained servos on a single bus (for example the head_pan and head_tilt servos). It allows for greater communication bandwidth by doing a group read/write over USB.
The EndOfArm class derives from DynamixelXChain to provide an extensible interface that supports a user in integrating additional degrees of freedom to the robot. The tutorial Adding Custom Wrist DoF explains how to do this.
DynamixelHelloXL430
DynamixelHelloXL430 provides an interface to servo motion that is consistent with the Stretch Body lift, arm, and base joints. It also manages the servo parameters and calibration. Let's explore this interface further. From iPython, let's look at the status message for DynamixelHelloXL430
import stretch_body.dynamixel_hello_XL430
m = stretch_body.dynamixel_hello_XL430.DynamixelHelloXL430('head_pan')
m.startup()
m.pretty_print()
Output:
----- HelloXL430 ------
Name head_pan
Position (rad) -0.0
Position (deg) -0.0
Position (ticks) 1250
Velocity (rad/s) -0.0
Velocity (ticks/s) 0
Effort (%) 0.0
Effort (ticks) 0
Temp 34.0
Comm Errors 0
Hardware Error 0
Hardware Error: Input Voltage Error: False
Hardware Error: Overheating Error: False
Hardware Error: Motor Encoder Error: False
Hardware Error: Electrical Shock Error: False
Hardware Error: Overload Error: False
Watchdog Errors: 0
Timestamp PC 1661552966.7202659
Range (ticks) [0, 3827]
Range (rad) [ 1.9174759848570513 , -3.953068490381297 ]
Stalled True
Stall Overload False
Is Calibrated 0
We see that it reports the position in both radians (with respect to the joint frame) and ticks (with respect to the servo encoder). DynamixelHelloXL430 handles the calibration between the two using its method ticks_to_world_rad through the following params:
stretch_params.py | grep head_pan | grep '_t '
Output:
stretch_configuration_params.yaml param.head_pan.range_t [0, 3827]
stretch_configuration_params.yaml param.head_pan.zero_t 1250
In addition to move_to and move_by, the class also implements a splined trajectory interface as discussed in the Splined Trajectory Tutorial.
DynamixelXL430
DynamixelXL430 provides a thin wrapper to the Robotis Dynamixel SDK. You may choose to interact with the servo at this level as well. For example, to jog the head_pan 200 ticks:
import stretch_body.dynamixel_XL430
import time
m = stretch_body.dynamixel_XL430.DynamixelXL430(11, '/dev/hello-dynamixel-head',baud=115200)
m.startup()
x=m.get_pos() #In encoder ticks
m.go_to_pos(x+200) #Move 200 ticks incremental
time.sleep(2.0)
m.stop()